✨ PLR_HEAT_BED_ON_REBOOT

MarlinFirmware/Marlin#26691

config/default/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/3DMatik/XL/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             28 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -1804,6 +1804,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Alfawise/U20/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AliExpress/CL-260/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/A2/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/A2plus/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/A6/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/A8/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/A8plus/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/A9/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/E10/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/E16/BTT SKR 1.3/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/E16/Stock/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/ET4+/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/ET4-Pro/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/ET4/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/ET4X/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/ET5-Pro/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/ET5/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Anet/ET5X/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AnyCubic/Chiron/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT      false  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     #define POWER_LOSS_PIN   OUTAGETEST_PIN // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AnyCubic/Mega Zero 2.0/Anycubic V1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AnyCubic/Mega Zero/Anycubic V1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AnyCubic/Mega Zero/BigTreeTech SKR Mini MZ V1.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AnyCubic/Vyper/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AnyCubic/i3 Mega/Trigorilla AVR/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AnyCubic/i3 Mega/Trigorilla Pro STM32/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/ArmEd/Configuration_adv.h

@@ -1800,6 +1800,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Artillery/Genius Pro/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Artillery/Genius/BLTouch/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Artillery/Genius/V1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Artillery/Hornet/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Artillery/Sidewinder X1/0.9 BMG - E3D V6/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Artillery/Sidewinder X1/V1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Artillery/Sidewinder X2/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Azteeg/X5GT/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIBO/TouchX/default - BLTouch/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -1792,6 +1792,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIQU/B1 SE Plus/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIQU/B1 SE/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIQU/B1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIQU/BX/all-metal-hotend/Configuration_adv.h

@@ -1798,6 +1798,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIQU/BX/base/Configuration_adv.h

@@ -1798,6 +1798,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIQU/Hurakan/Configuration_adv.h

@@ -1796,6 +1796,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BIQU/Thunder Standard/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -1803,6 +1803,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/CNC/miniRambo/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/CTC/A13/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/CTC/Bizer/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/CTC/i3 2560 Rev A/no probe/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Cartesio/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Copymaster3D/300/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Copymaster3D/400/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Copymaster3D/500/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 Max/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 Mini/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 Mini/CrealityV1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 Mini/MEEB-3DP/Configuration_adv.h

@@ -1794,6 +1794,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 S4/CrealityV1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 1.2 with TFT35 E3 V3.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 S5/BigTreeTech SKR Mini E3 v3/Configuration_adv.h

@@ -1796,6 +1796,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 S5/CrealityV1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 S5/CrealityV2.2 - BLTouch/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 S5/CrealityV427 - BLTouch/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 V2/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 V3/BigTreeTech SKR Mini E3 v3/Configuration_adv.h

@@ -1797,6 +1797,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10 V3/Stock/Configuration_adv.h

@@ -1797,6 +1797,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10/CrealityV1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10S Pro/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10S/BigTreeTech SKR 1.4 Turbo TMC2209/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10S/BigTreeTech SKR 2.0 TMC2209/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 2.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10S/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10S/BigTreeTech SKR Pro v1.2/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10S/CrealityV1 - BLTouch/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-10S/CrealityV1/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-20 Pro/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-20/RepRapWorld Minitronics20/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-20/Stock/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-30 PrintMill/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-6 SE/Configuration_adv.h

@@ -1796,6 +1796,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/CR-8/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/Ender-2 Pro/CrealityV423/Configuration_adv.h

@@ -1796,6 +1796,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       false // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/Ender-3 Max Neo/BigTreeTech SKR Mini E3 3.0/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/Ender-3 Max Neo/CrealityV422/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.

config/examples/Creality/Ender-3 Max/Configuration_adv.h

@@ -1795,6 +1795,8 @@
   #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT       true  // Power-Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
+    //#define PLR_HEAT_BED_ON_REBOOT        // Heat up bed immediately on reboot to mitigate object detaching/warping.
+    //#define PLR_HEAT_BED_EXTRA          0 // (°C) Relative increase of bed temperature for better adhesion (limited by max temp).
     //#define PLR_BED_THRESHOLD BED_MAXTEMP // (°C) Skip user confirmation at or above this bed temperature (0 to disable)
 
     //#define POWER_LOSS_PIN             44 // Pin to detect power-loss. Set to -1 to disable default pin on boards without module, or comment to use board default.