{
  "type": "filament",
  "filament_id": "GFB99",
  "setting_id": "GFSA04",
  "instantiation": "true",
  "from": "system",
  "activate_air_filtration": ["0"],
  "activate_chamber_temp_control": ["0"],
  "additional_cooling_fan_speed": ["0"],
  "chamber_temperature": ["0"],
  "close_fan_the_first_x_layers": ["2"],
  "compatible_printers": [
    "Flashforge Guider 3 Ultra 0.4 Nozzle",
    "Flashforge Guider 3 Ultra 0.6 Nozzle",
    "Flashforge Guider 3 Ultra 0.8 Nozzle",
    "Flashforge Guider 2s 0.4 nozzle"
  ],
  "compatible_printers_condition": "",
  "compatible_prints": [],
  "compatible_prints_condition": "",
  "complete_print_exhaust_fan_speed": ["80"],
  "cool_plate_temp": ["80"],
  "cool_plate_temp_initial_layer": ["80"],
  "default_filament_colour": [""],
  "during_print_exhaust_fan_speed": ["60"],
  "enable_overhang_bridge_fan": ["1"],
  "enable_pressure_advance": ["1"],
  "eng_plate_temp": ["80"],
  "eng_plate_temp_initial_layer": ["80"],
  "fan_cooling_layer_time": ["30"],
  "fan_max_speed": ["30"],
  "fan_min_speed": ["10"],
  "filament_cooling_final_speed": ["3.4"],
  "filament_cooling_initial_speed": ["2.2"],
  "filament_cooling_moves": ["4"],
  "filament_cost": ["20"],
  "filament_density": ["1.04"],
  "filament_deretraction_speed": ["nil"],
  "filament_diameter": ["1.75"],
  "filament_end_gcode": ["; filament end gcode\n"],
  "filament_flow_ratio": ["1.02"],
  "filament_is_support": ["0"],
  "filament_load_time": ["0"],
  "filament_loading_speed": ["28"],
  "filament_loading_speed_start": ["3"],
  "filament_max_volumetric_speed": ["18"],
  "filament_minimal_purge_on_wipe_tower": ["10"],
  "filament_multitool_ramming": ["0"],
  "filament_multitool_ramming_flow": ["10"],
  "filament_multitool_ramming_volume": ["10"],
  "filament_notes": [""],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_before_wipe": ["nil"],
  "filament_retract_lift_above": ["nil"],
  "filament_retract_lift_below": ["nil"],
  "filament_retract_lift_enforce": ["nil"],
  "filament_retract_restart_extra": ["nil"],
  "filament_retract_when_changing_layer": ["nil"],
  "filament_retraction_length": ["nil"],
  "filament_retraction_minimum_travel": ["nil"],
  "filament_retraction_speed": ["nil"],
  "filament_settings_id": ["Flashforge Generic ASA @G3U"],
  "filament_shrink": ["100%"],
  "filament_soluble": ["0"],
  "filament_start_gcode": ["; filament start gcode\n"],
  "filament_toolchange_delay": ["0"],
  "filament_type": ["ASA"],
  "filament_unload_time": ["0"],
  "filament_unloading_speed": ["35"],
  "filament_unloading_speed_start": ["40"],
  "filament_vendor": ["Generic"],
  "filament_wipe": ["nil"],
  "filament_wipe_distance": ["nil"],
  "filament_z_hop": ["nil"],
  "filament_z_hop_types": ["nil"],
  "full_fan_speed_layer": ["0"],
  "hot_plate_temp": ["105"],
  "hot_plate_temp_initial_layer": ["105"],
  "inherits": "Flashforge Generic ABS",
  "name": "Flashforge Generic ASA @G3U",
  "nozzle_temperature": ["240"],
  "nozzle_temperature_initial_layer": ["240"],
  "nozzle_temperature_range_high": ["260"],
  "nozzle_temperature_range_low": ["220"],
  "overhang_fan_speed": ["50"],
  "overhang_fan_threshold": ["25%"],
  "pressure_advance": ["0.036"],
  "reduce_fan_stop_start_freq": ["1"],
  "required_nozzle_HRC": ["0"],
  "slow_down_for_layer_cooling": ["1"],
  "slow_down_layer_time": ["8"],
  "slow_down_min_speed": ["20"],
  "support_material_interface_fan_speed": ["40"],
  "temperature_vitrification": ["100"],
  "textured_plate_temp": ["80"],
  "textured_plate_temp_initial_layer": ["80"],
  "version": "1.9.0.2"
}