diff --git a/config/examples/Creality/CR-6 SE/Configuration.h b/config/examples/Creality/CR-6 SE/Configuration.h index 054e90d8d9..6abd08c527 100644 --- a/config/examples/Creality/CR-6 SE/Configuration.h +++ b/config/examples/Creality/CR-6 SE/Configuration.h @@ -70,7 +70,7 @@ // @section info // Author info of this build printed to the host during boot and M115 -#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. +#define STRING_CONFIG_H_AUTHOR "CR-6 SE" // Who made the changes. //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes) /** @@ -103,14 +103,14 @@ * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ -#define SERIAL_PORT 0 +#define SERIAL_PORT 1 /** * Select a secondary serial port on the board to use for communication with the host. * Currently Ethernet (-2) is only supported on Teensy 4.1 boards. * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7] */ -//#define SERIAL_PORT_2 -1 +//#define SERIAL_PORT_2 3 /** * This setting determines the communication speed of the printer. @@ -121,14 +121,14 @@ * * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] */ -#define BAUDRATE 250000 +#define BAUDRATE 115200 // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH // Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD - #define MOTHERBOARD BOARD_RAMPS_14_EFB + #define MOTHERBOARD BOARD_CREALITY_V452 #endif // Name displayed in the LCD "Ready" message and Info menu @@ -427,7 +427,7 @@ #define TEMP_SENSOR_5 0 #define TEMP_SENSOR_6 0 #define TEMP_SENSOR_7 0 -#define TEMP_SENSOR_BED 0 +#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_PROBE 0 #define TEMP_SENSOR_CHAMBER 0 @@ -456,7 +456,7 @@ // Below this temperature the heater will be switched off // because it probably indicates a broken thermistor wire. -#define HEATER_0_MINTEMP 5 +#define HEATER_0_MINTEMP 0 #define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5 #define HEATER_3_MINTEMP 5 @@ -464,7 +464,7 @@ #define HEATER_5_MINTEMP 5 #define HEATER_6_MINTEMP 5 #define HEATER_7_MINTEMP 5 -#define BED_MINTEMP 5 +#define BED_MINTEMP 0 // Above this temperature the heater will be switched off. // This can protect components from overheating, but NOT from shorts and failures. @@ -477,7 +477,7 @@ #define HEATER_5_MAXTEMP 275 #define HEATER_6_MAXTEMP 275 #define HEATER_7_MAXTEMP 275 -#define BED_MAXTEMP 150 +#define BED_MAXTEMP 120 //=========================================================================== //============================= PID Settings ================================ @@ -503,9 +503,9 @@ #define DEFAULT_Ki_LIST { 1.08, 1.08 } #define DEFAULT_Kd_LIST { 114.00, 114.00 } #else - #define DEFAULT_Kp 22.20 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114.00 + #define DEFAULT_Kp 14.32 + #define DEFAULT_Ki 0.81 + #define DEFAULT_Kd 63.12 #endif #endif // PIDTEMP @@ -526,7 +526,7 @@ * heater. If your configuration is significantly different than this and you don't understand * the issues involved, don't use bed PID until someone else verifies that your hardware works. */ -//#define PIDTEMPBED +#define PIDTEMPBED //#define BED_LIMIT_SWITCHING @@ -544,9 +544,9 @@ // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 + #define DEFAULT_bedKp 79.49 + #define DEFAULT_bedKi 1.17 + #define DEFAULT_bedKd 1349.52 // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. #endif // PIDTEMPBED @@ -569,14 +569,14 @@ * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** */ #define PREVENT_COLD_EXTRUSION -#define EXTRUDE_MINTEMP 170 +#define EXTRUDE_MINTEMP 180 /** * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. * Note: For Bowden Extruders make this large enough to allow load/unload. */ #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH 200 +#define EXTRUDE_MAXLENGTH 1000 //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -597,7 +597,7 @@ #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed -#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber +//#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber //=========================================================================== //============================= Mechanical Settings ========================= @@ -682,15 +682,15 @@ * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] */ -#define X_DRIVER_TYPE A4988 -#define Y_DRIVER_TYPE A4988 -#define Z_DRIVER_TYPE A4988 +#define X_DRIVER_TYPE TMC2209_STANDALONE +#define Y_DRIVER_TYPE TMC2209_STANDALONE +#define Z_DRIVER_TYPE TMC2209_STANDALONE //#define X2_DRIVER_TYPE A4988 //#define Y2_DRIVER_TYPE A4988 //#define Z2_DRIVER_TYPE A4988 //#define Z3_DRIVER_TYPE A4988 //#define Z4_DRIVER_TYPE A4988 -#define E0_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE TMC2209_STANDALONE //#define E1_DRIVER_TYPE A4988 //#define E2_DRIVER_TYPE A4988 //#define E3_DRIVER_TYPE A4988 @@ -745,14 +745,14 @@ * Override with M92 * X, Y, Z, E0 [, E1[, E2...]] */ -#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 } +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 } /** * Default Max Feed Rate (mm/s) * Override with M203 * X, Y, Z, E0 [, E1[, E2...]] */ -#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2 #if ENABLED(LIMITED_MAX_FR_EDITING) @@ -765,7 +765,7 @@ * Override with M201 * X, Y, Z, E0 [, E1[, E2...]] */ -#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } +#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 1000 } //#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2 #if ENABLED(LIMITED_MAX_ACCEL_EDITING) @@ -780,9 +780,9 @@ * M204 R Retract Acceleration * M204 T Travel Acceleration */ -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves /** * Default Jerk limits (mm/s) @@ -816,7 +816,7 @@ * https://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html */ #if DISABLED(CLASSIC_JERK) - #define JUNCTION_DEVIATION_MM 0.013 // (mm) Distance from real junction edge + #define JUNCTION_DEVIATION_MM 0.05 // (mm) Distance from real junction edge #define JD_HANDLE_SMALL_SEGMENTS // Use curvature estimation instead of just the junction angle // for small segments (< 1mm) with large junction angles (> 135°). #endif @@ -829,7 +829,7 @@ * * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained */ -//#define S_CURVE_ACCELERATION +#define S_CURVE_ACCELERATION //=========================================================================== //============================= Z Probe Options ============================= @@ -848,7 +848,7 @@ #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN // Force the use of the probe for Z-axis homing -//#define USE_PROBE_FOR_Z_HOMING +#define USE_PROBE_FOR_Z_HOMING /** * Z_MIN_PROBE_PIN @@ -886,7 +886,7 @@ * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. * (e.g., an inductive probe or a nozzle-based probe-switch.) */ -//#define FIX_MOUNTED_PROBE +#define FIX_MOUNTED_PROBE /** * Use the nozzle as the probe, as with a conductive @@ -894,6 +894,16 @@ */ //#define NOZZLE_AS_PROBE +/** + * Auto-leveling needs preheating + */ +#define AUTOLEVEL_NEEDS_PREHEATING + +#if ENABLED(AUTOLEVEL_NEEDS_PREHEATING) + #define AUTOLEVEL_PREHEAT_NOZZLE_TEMP 120 + #define AUTOLEVEL_PREHEAT_BED_TEMP 50 +#endif + /** * Z Servo Probe, such as an endstop switch on a rotating arm. */ @@ -990,11 +1000,11 @@ * | [-] | * O-- FRONT --+ */ -#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 } +#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0.2 } // Most probes should stay away from the edges of the bed, but // with NOZZLE_AS_PROBE this can be negative for a wider probing area. -#define PROBING_MARGIN 10 +#define PROBING_MARGIN 30 // X and Y axis travel speed (mm/min) between probes #define XY_PROBE_SPEED (133*60) @@ -1014,7 +1024,7 @@ * A total of 2 does fast/slow probes with a weighted average. * A total of 3 or more adds more slow probes, taking the average. */ -//#define MULTIPLE_PROBING 2 +#define MULTIPLE_PROBING 2 //#define EXTRA_PROBING 1 /** @@ -1032,15 +1042,15 @@ * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. */ #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow -#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points -#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +#define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 2 // Z Clearance between multiple probes //#define Z_AFTER_PROBING 5 // Z position after probing is done #define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping // For M851 give a range for adjusting the Z probe offset -#define Z_PROBE_OFFSET_RANGE_MIN -20 -#define Z_PROBE_OFFSET_RANGE_MAX 20 +#define Z_PROBE_OFFSET_RANGE_MIN -10 +#define Z_PROBE_OFFSET_RANGE_MAX 10 // Enable the M48 repeatability test to test probe accuracy //#define Z_MIN_PROBE_REPEATABILITY_TEST @@ -1090,14 +1100,14 @@ // @section machine // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. -#define INVERT_X_DIR false -#define INVERT_Y_DIR true -#define INVERT_Z_DIR false +#define INVERT_X_DIR true +#define INVERT_Y_DIR false +#define INVERT_Z_DIR true // @section extruder // For direct drive extruder v9 set to true, for geared extruder set to false. -#define INVERT_E0_DIR false +#define INVERT_E0_DIR true #define INVERT_E1_DIR false #define INVERT_E2_DIR false #define INVERT_E3_DIR false @@ -1112,10 +1122,10 @@ //#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. -//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... +#define Z_HOMING_HEIGHT 15 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding. -//#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z +#define Z_AFTER_HOMING 5 // (mm) Height to move to after homing Z // Direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1] @@ -1126,16 +1136,16 @@ // @section machine // The size of the print bed -#define X_BED_SIZE 200 -#define Y_BED_SIZE 200 +#define X_BED_SIZE 235 +#define Y_BED_SIZE 235 // Travel limits (mm) after homing, corresponding to endstop positions. -#define X_MIN_POS 0 -#define Y_MIN_POS 0 +#define X_MIN_POS -5 +#define Y_MIN_POS -2 #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZE #define Y_MAX_POS Y_BED_SIZE -#define Z_MAX_POS 200 +#define Z_MAX_POS 250 /** * Software Endstops @@ -1147,7 +1157,7 @@ */ // Min software endstops constrain movement within minimum coordinate bounds -#define MIN_SOFTWARE_ENDSTOPS +//#define MIN_SOFTWARE_ENDSTOPS #if ENABLED(MIN_SOFTWARE_ENDSTOPS) #define MIN_SOFTWARE_ENDSTOP_X #define MIN_SOFTWARE_ENDSTOP_Y @@ -1173,17 +1183,17 @@ * RAMPS-based boards use SERVO3_PIN for the first runout sensor. * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. */ -//#define FILAMENT_RUNOUT_SENSOR +#define FILAMENT_RUNOUT_SENSOR #if ENABLED(FILAMENT_RUNOUT_SENSOR) #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500. #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. - #define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present. + #define FIL_RUNOUT_STATE HIGH // Pin state indicating that filament is NOT present. #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. // Set one or more commands to execute on filament runout. // (After 'M412 H' Marlin will ask the host to handle the process.) - #define FILAMENT_RUNOUT_SCRIPT "M600" + #define FILAMENT_RUNOUT_SCRIPT "M25" // After a runout is detected, continue printing this length of filament // before executing the runout script. Useful for a sensor at the end of @@ -1238,7 +1248,7 @@ */ //#define AUTO_BED_LEVELING_3POINT //#define AUTO_BED_LEVELING_LINEAR -//#define AUTO_BED_LEVELING_BILINEAR +#define AUTO_BED_LEVELING_BILINEAR //#define AUTO_BED_LEVELING_UBL //#define MESH_BED_LEVELING @@ -1246,14 +1256,14 @@ * Normally G28 leaves leveling disabled on completion. Enable * this option to have G28 restore the prior leveling state. */ -//#define RESTORE_LEVELING_AFTER_G28 +#define RESTORE_LEVELING_AFTER_G28 /** * Enable detailed logging of G28, G29, M48, etc. * Turn on with the command 'M111 S32'. * NOTE: Requires a lot of PROGMEM! */ -//#define DEBUG_LEVELING_FEATURE +#define DEBUG_LEVELING_FEATURE #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) // Gradually reduce leveling correction until a set height is reached, @@ -1270,7 +1280,7 @@ /** * Enable the G26 Mesh Validation Pattern tool. */ - //#define G26_MESH_VALIDATION + #define G26_MESH_VALIDATION #if ENABLED(G26_MESH_VALIDATION) #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. @@ -1285,17 +1295,17 @@ #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) // Set the number of grid points per dimension. - #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_X 4 #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Probe along the Y axis, advancing X after each column - //#define PROBE_Y_FIRST + #define PROBE_Y_FIRST #if ENABLED(AUTO_BED_LEVELING_BILINEAR) // Beyond the probed grid, continue the implied tilt? // Default is to maintain the height of the nearest edge. - //#define EXTRAPOLATE_BEYOND_GRID + #define EXTRAPOLATE_BEYOND_GRID // // Experimental Subdivision of the grid by Catmull-Rom method. @@ -1389,7 +1399,7 @@ // - Move the Z probe (or nozzle) to a defined XY point before Z Homing. // - Prevent Z homing when the Z probe is outside bed area. // -//#define Z_SAFE_HOMING +#define Z_SAFE_HOMING #if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing @@ -1475,12 +1485,12 @@ * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) */ -//#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! -#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +//#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. #define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load #if ENABLED(EEPROM_SETTINGS) - //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. + #define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. #endif // @@ -1507,14 +1517,14 @@ // Preheat Constants #define PREHEAT_1_LABEL "PLA" -#define PREHEAT_1_TEMP_HOTEND 180 -#define PREHEAT_1_TEMP_BED 70 -#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 +#define PREHEAT_1_TEMP_HOTEND 200 +#define PREHEAT_1_TEMP_BED 60 +#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255 #define PREHEAT_2_LABEL "ABS" #define PREHEAT_2_TEMP_HOTEND 240 -#define PREHEAT_2_TEMP_BED 110 -#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 +#define PREHEAT_2_TEMP_BED 70 +#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255 /** * Nozzle Park @@ -1527,7 +1537,7 @@ * P1 Raise the nozzle always to Z-park height. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. */ -//#define NOZZLE_PARK_FEATURE +#define NOZZLE_PARK_FEATURE #if ENABLED(NOZZLE_PARK_FEATURE) // Specify a park position as { X, Y, Z_raise } @@ -1728,7 +1738,7 @@ * SD Card support is disabled by default. If your controller has an SD slot, * you must uncomment the following option or it won't work. */ -//#define SDSUPPORT +#define SDSUPPORT /** * SD CARD: SPI SPEED @@ -1816,7 +1826,7 @@ // If you have a speaker that can produce tones, enable it here. // By default Marlin assumes you have a buzzer with a fixed frequency. // -//#define SPEAKER +#define SPEAKER // // The duration and frequency for the UI feedback sound. @@ -1825,8 +1835,8 @@ // Note: Test audio output with the G-Code: // M300 S P // -//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 -//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 +#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +#define LCD_FEEDBACK_FREQUENCY_HZ 5000 //============================================================================= //======================== LCD / Controller Selection ========================= @@ -2170,6 +2180,11 @@ //#define DGUS_LCD_UI_FYSETC //#define DGUS_LCD_UI_HIPRECY +// +// CR-6 OEM touch screen. A DWIN display with touch. +// +#define DGUS_LCD_UI_CREALITY_TOUCH + // // Touch-screen LCD for Malyan M200/M300 printers // diff --git a/config/examples/Creality/CR-6 SE/Configuration_adv.h b/config/examples/Creality/CR-6 SE/Configuration_adv.h index 9e1e0feab7..f6897d3f04 100644 --- a/config/examples/Creality/CR-6 SE/Configuration_adv.h +++ b/config/examples/Creality/CR-6 SE/Configuration_adv.h @@ -186,7 +186,7 @@ * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD */ #if ENABLED(THERMAL_PROTECTION_HOTENDS) - #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_PERIOD 60 // Seconds #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops @@ -206,7 +206,7 @@ * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set * below 2. */ - #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_PERIOD 60 // Seconds #define WATCH_TEMP_INCREASE 2 // Degrees Celsius #endif @@ -214,13 +214,13 @@ * Thermal Protection parameters for the bed are just as above for hotends. */ #if ENABLED(THERMAL_PROTECTION_BED) - #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_PERIOD 180 // Seconds #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius /** * As described above, except for the bed (M140/M190/M303). */ - #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_PERIOD 180 // Seconds #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #endif @@ -430,7 +430,7 @@ * * Define one or both of these to override the default 0-255 range. */ -//#define FAN_MIN_PWM 50 +#define FAN_MIN_PWM 50 //#define FAN_MAX_PWM 128 /** @@ -503,7 +503,7 @@ /** * M355 Case Light on-off / brightness */ -//#define CASE_LIGHT_ENABLE +#define CASE_LIGHT_ENABLE #if ENABLED(CASE_LIGHT_ENABLE) //#define CASE_LIGHT_PIN 4 // Override the default pin if needed #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW @@ -658,7 +658,7 @@ //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (mm) Backoff from endstops after homing -//#define QUICK_HOME // If G28 contains XY do a diagonal move first +#define QUICK_HOME // If G28 contains XY do a diagonal move first //#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X //#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first @@ -1060,8 +1060,9 @@ // Change values more rapidly when the encoder is rotated faster #define ENCODER_RATE_MULTIPLIER #if ENABLED(ENCODER_RATE_MULTIPLIER) - #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed - #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed + #define ENCODER_5X_STEPS_PER_SEC 30 + #define ENCODER_10X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 130 // (steps/s) Encoder rate for 100x speed #endif // Play a beep when the feedrate is changed from the Status Screen @@ -1184,7 +1185,7 @@ //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files - #define EVENT_GCODE_SD_ABORT "G28XY" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27") + #define EVENT_GCODE_SD_ABORT "G27\nM84" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27") #if ENABLED(PRINTER_EVENT_LEDS) #define PE_LEDS_COMPLETED_TIME (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination @@ -1198,9 +1199,9 @@ * an option on the LCD screen to continue the print from the last-known * point in the file. */ - //#define POWER_LOSS_RECOVERY + #define POWER_LOSS_RECOVERY #if ENABLED(POWER_LOSS_RECOVERY) - #define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) + #define PLR_ENABLED_DEFAULT true // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500) //#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss //#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled! //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) @@ -1238,7 +1239,7 @@ * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) */ - //#define SDCARD_SORT_ALPHA + #define SDCARD_SORT_ALPHA // SD Card Sorting options #if ENABLED(SDCARD_SORT_ALPHA) @@ -1606,7 +1607,7 @@ * * Warning: Does not respect endstops! */ -//#define BABYSTEPPING +#define BABYSTEPPING #if ENABLED(BABYSTEPPING) //#define INTEGRATED_BABYSTEPPING // EXPERIMENTAL integration of babystepping into the Stepper ISR //#define BABYSTEP_WITHOUT_HOMING @@ -1614,7 +1615,7 @@ //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way //#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps - #define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep + #define BABYSTEP_MULTIPLICATOR_Z 40 // (steps or mm) Steps or millimeter distance for each Z babystep #define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. @@ -1629,7 +1630,7 @@ //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 - //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping #if ENABLED(BABYSTEP_ZPROBE_OFFSET) //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor @@ -1653,12 +1654,12 @@ * * See https://marlinfw.org/docs/features/lin_advance.html for full instructions. */ -//#define LIN_ADVANCE +#define LIN_ADVANCE #if ENABLED(LIN_ADVANCE) //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants - #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + #define LIN_ADVANCE_K 0 // Unit: mm compression per 1mm/s extruder speed //#define LA_DEBUG // If enabled, this will generate debug information output over USB. - //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration + #define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration #endif // @section leveling @@ -1947,7 +1948,7 @@ * Currently handles M108, M112, M410, M876 * NOTE: Not yet implemented for all platforms. */ -//#define EMERGENCY_PARSER +#define EMERGENCY_PARSER // Bad Serial-connections can miss a received command by sending an 'ok' // Therefore some clients abort after 30 seconds in a timeout. @@ -2090,7 +2091,7 @@ * Requires NOZZLE_PARK_FEATURE. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. */ -//#define ADVANCED_PAUSE_FEATURE +#define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. @@ -2124,7 +2125,7 @@ #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. #define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload - #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define PAUSE_PARK_NOZZLE_TIMEOUT 90 // (seconds) Time limit before the nozzle is turned off for safety. #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. @@ -3532,29 +3533,30 @@ // Add an LCD menu for MMU2 //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Průša MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 1145 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } - // Settings for filament load / unload. - // This is for Průša MK3-style extruders. Customize for your hardware. - #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 - #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ - { 7.2, 1145 }, \ - { 14.4, 871 }, \ - { 36.0, 1393 }, \ - { 14.4, 871 }, \ - { 50.0, 198 } - - #define MMU2_RAMMING_SEQUENCE \ - { 1.0, 1000 }, \ - { 1.0, 1500 }, \ - { 2.0, 2000 }, \ - { 1.5, 3000 }, \ - { 2.5, 4000 }, \ - { -15.0, 5000 }, \ - { -14.0, 1200 }, \ - { -6.0, 600 }, \ - { 10.0, 700 }, \ - { -10.0, 400 }, \ - { -50.0, 2000 } + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + #endif /** * MMU Extruder Sensor