diff --git a/config/examples/AnyCubic/Chiron/Configuration.h b/config/examples/AnyCubic/Chiron/Configuration.h
index 246299c7c0..839065e065 100644
--- a/config/examples/AnyCubic/Chiron/Configuration.h
+++ b/config/examples/AnyCubic/Chiron/Configuration.h
@@ -1042,10 +1042,10 @@
 #define Z_CLEARANCE_MULTI_PROBE     3 // Z Clearance between multiple probes
 //#define Z_AFTER_PROBING           5 // Z position after probing is done
 
-#define Z_PROBE_LOW_POINT          -7 // Farthest distance below the trigger-point to go before stopping
+#define Z_PROBE_LOW_POINT          -10 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -25
+#define Z_PROBE_OFFSET_RANGE_MIN -30
 #define Z_PROBE_OFFSET_RANGE_MAX 10
 
 // Enable the M48 repeatability test to test probe accuracy
@@ -1200,7 +1200,7 @@
   // After a runout is detected, continue printing this length of filament
   // before executing the runout script. Useful for a sensor at the end of
   // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
-  //#define FILAMENT_RUNOUT_DISTANCE_MM 25
+  #define FILAMENT_RUNOUT_DISTANCE_MM 25
 
   #ifdef FILAMENT_RUNOUT_DISTANCE_MM
     // Enable this option to use an encoder disc that toggles the runout pin
diff --git a/config/examples/AnyCubic/Chiron/Configuration_adv.h b/config/examples/AnyCubic/Chiron/Configuration_adv.h
index 79b218a9ee..780f6dd595 100644
--- a/config/examples/AnyCubic/Chiron/Configuration_adv.h
+++ b/config/examples/AnyCubic/Chiron/Configuration_adv.h
@@ -187,9 +187,9 @@
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
   #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_HYSTERESIS 10    // Degrees Celsius
 
-  //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+  #define ADAPTIVE_FAN_SLOWING                // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
     //#define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
   #endif
@@ -206,7 +206,7 @@
    * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
    * below 2.
    */
-  #define WATCH_TEMP_PERIOD 20                // Seconds
+  #define WATCH_TEMP_PERIOD  30               // Seconds
   #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
@@ -215,7 +215,7 @@
  */
 #if ENABLED(THERMAL_PROTECTION_BED)
   #define THERMAL_PROTECTION_BED_PERIOD        20 // Seconds
-  #define THERMAL_PROTECTION_BED_HYSTERESIS     2 // Degrees Celsius
+  #define THERMAL_PROTECTION_BED_HYSTERESIS     4 // Degrees Celsius
 
   /**
    * As described above, except for the bed (M140/M190/M303).