diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h
index 173e2f03de..78a61f3483 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.0/Configuration_adv.h	
@@ -1280,18 +1280,16 @@
   // Add an optimized binary file transfer mode, initiated with 'M28 B1'
   //#define BINARY_FILE_TRANSFER
 
-  #if HAS_SDCARD_CONNECTION
-    /**
-     * Set this option to one of the following (or the board's defaults apply):
-     *
-     *           LCD - Use the SD drive in the external LCD controller.
-     *       ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
-     *  CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
-     *
-     * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
-     */
-    #define SDCARD_CONNECTION ONBOARD
-  #endif
+  /**
+   * Set this option to one of the following (or the board's defaults apply):
+   *
+   *           LCD - Use the SD drive in the external LCD controller.
+   *       ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
+   *  CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
+   *
+   * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
+   */
+  #define SDCARD_CONNECTION ONBOARD
 
 #endif // SDSUPPORT
 
diff --git a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h
index 8e4e882928..ed6cc751d5 100644
--- a/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h	
+++ b/config/examples/Creality/Ender-3/BigTreeTech SKR Mini E3 1.2/Configuration_adv.h	
@@ -1280,18 +1280,16 @@
   // Add an optimized binary file transfer mode, initiated with 'M28 B1'
   //#define BINARY_FILE_TRANSFER
 
-  #if HAS_SDCARD_CONNECTION
-    /**
-     * Set this option to one of the following (or the board's defaults apply):
-     *
-     *           LCD - Use the SD drive in the external LCD controller.
-     *       ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
-     *  CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
-     *
-     * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
-     */
-    #define SDCARD_CONNECTION ONBOARD
-  #endif
+  /**
+   * Set this option to one of the following (or the board's defaults apply):
+   *
+   *           LCD - Use the SD drive in the external LCD controller.
+   *       ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.)
+   *  CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file).
+   *
+   * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
+   */
+  #define SDCARD_CONNECTION ONBOARD
 
 #endif // SDSUPPORT