From 4fd9fd436c8ee20e4a75d5b2d560bad413706faa Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Wed, 23 Dec 2020 18:03:15 -0600 Subject: [PATCH] Update some configs --- config/examples/Anet/ET4+/Configuration_adv.h | 3 ++- .../Ender-3/CrealityV422/Configuration_adv.h | 16 +++++++++++----- 2 files changed, 13 insertions(+), 6 deletions(-) diff --git a/config/examples/Anet/ET4+/Configuration_adv.h b/config/examples/Anet/ET4+/Configuration_adv.h index a1c8c9df7f..5e104a8080 100644 --- a/config/examples/Anet/ET4+/Configuration_adv.h +++ b/config/examples/Anet/ET4+/Configuration_adv.h @@ -1227,7 +1227,8 @@ //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. #define POWER_LOSS_STATE LOW // State of pin indicating power loss - //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate + //#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor + //#define POWER_LOSS_PULLDOWN //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h b/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h index 4044c19c0d..3a8e3c16ac 100644 --- a/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h @@ -854,8 +854,6 @@ // If the Nozzle or Bed falls when the Z stepper is disabled, set its resting position here. //#define Z_AFTER_DEACTIVATE Z_HOME_POS -//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated - // Default Minimum Feedrates for printing and travel moves #define DEFAULT_MINIMUMFEEDRATE 0.0 // (mm/s) Minimum feedrate. Set with M205 S. #define DEFAULT_MINTRAVELFEEDRATE 0.0 // (mm/s) Minimum travel feedrate. Set with M205 T. @@ -1084,8 +1082,15 @@ #if HAS_BED_PROBE //#define PROBE_OFFSET_WIZARD #if ENABLED(PROBE_OFFSET_WIZARD) - #define PROBE_OFFSET_WIZARD_START_Z -4.0 // Estimated nozzle-to-probe Z offset, plus a little extra - //#define PROBE_OFFSET_WIZARD_XY_POS XY_CENTER // Set a convenient position to do the measurement + // + // Enable to init the Probe Z-Offset when starting the Wizard. + // Use a height slightly above the estimated nozzle-to-probe Z offset. + // For example, with an offset of -5, consider a starting height of -4. + // + //#define PROBE_OFFSET_WIZARD_START_Z -4.0 + + // Set a convenient position to do the calibration (probing point and nozzle/bed-distance) + //#define PROBE_OFFSET_WIZARD_XY_POS { X_CENTER, Y_CENTER } #endif #endif @@ -1222,7 +1227,8 @@ //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss - //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate + //#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor + //#define POWER_LOSS_PULLDOWN //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.