diff --git a/config/default/Configuration.h b/config/default/Configuration.h
index d816def5cb..cc07f81ffa 100644
--- a/config/default/Configuration.h
+++ b/config/default/Configuration.h
@@ -486,6 +486,7 @@
   //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
+
   #if ENABLED(PID_PARAMS_PER_HOTEND)
     // Specify between 1 and HOTENDS values per array.
     // If fewer than EXTRUDER values are provided, the last element will be repeated.
diff --git a/config/examples/Creality/Ender-3 V2/Configuration.h b/config/examples/Creality/Ender-3 V2/Configuration.h
index 5808499c1d..5169d12d3d 100644
--- a/config/examples/Creality/Ender-3 V2/Configuration.h	
+++ b/config/examples/Creality/Ender-3 V2/Configuration.h	
@@ -486,6 +486,7 @@
   //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
+
   #if ENABLED(PID_PARAMS_PER_HOTEND)
     // Specify between 1 and HOTENDS values per array.
     // If fewer than EXTRUDER values are provided, the last element will be repeated.
diff --git a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h
index d36ad49e22..8b02a56c02 100644
--- a/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h	
+++ b/config/examples/Creality/Ender-5/BigTreeTech SKR 1.4 Turbo (TMC2209)/Configuration.h	
@@ -506,13 +506,8 @@
 #if ENABLED(PIDTEMP)
   #define PID_EDIT_MENU           // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
   #define PID_AUTOTUNE_MENU       // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
-  //#define PID_DEBUG             // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
-  //#define PID_OPENLOOP 1        // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
-  //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
-  #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
-                                  // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
   // Creality Ender-5
   #if ENABLED(PID_PARAMS_PER_HOTEND)
@@ -771,14 +766,14 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 800, 93}
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 800, 93 }
 
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 500, 500, 5, 25}
+#define DEFAULT_MAX_FEEDRATE          { 500, 500, 5, 25 }
 
 //#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
@@ -791,7 +786,7 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 500, 500, 100, 5000}
+#define DEFAULT_MAX_ACCELERATION      { 500, 500, 100, 5000 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)